SCU 1000 & SCU 2000
The new control units SCU1000 (fixed mains connection via a cable) and SCU2000 (plug-in mains connection) from RNA have been completely redesigned and replace the current ESG1000 and ESG2000 series. The innovative design enables intuitive operation and easy integration into state-of-the-art equipment. The good-sized display provides a clear and intuitive user interface, and the front panel connections permit multiple control units to be directly arranged side-by-side. Use of the latest processor and communication technologies guarantees optimum operation of the control units.
General features and functions:
The compact control unit supplies all RNA vibrating drives with load currents up to 6 amps and is designed for stand-alone installation directly at the vibrating drive. Feed rates are optimized for RNA drives and can be precisely adjusted within the setting range via the LED display. A novel closed-loop control function keeps the feed rate almost constant even if fluctuations in the mains voltage occur. The illuminated rocker switch on the controller front panel disconnects all poles from power supply. For frequent switching applications or when operating with a higher-level control system provision is made for no-load switching-off both by floating contact and by a 16-30 VDC voltage signal. Moreover, the current operating status of the control system can be monitored by means of a "READY" or "ACTIVE" signal. The controller can operate on both 230V and 110V supplies which can be selected on an internal switch. All other controller settings are made via the LED display.
|Power supply (can be changed internally):||230 Volt AC, 50/60 Hz, +10 -10% oder
110 Volt AC, 50/60 Hz , +15 -6%
|Output voltage:||40...208 Volt (eff.) adjustable, (230V Netz)
20...105 Volr (eff.) adjustable, (110V Netz)
|Load current:||max. 6A (eff.)|
|Fuses (in power input):||2 miniature fuses, 5 x 20mm, M6.3A/250VAC|
1. asymmetric half-wave mode
|Mode change:||Coding jumper in load connector|
|Enabling of functions:||internal/external, adjustable via parameters|
|Enabling input, external contact:||floating, normally-open contact, approx. 24VDC, <10mA|
|Enabling input, external 24V signal:||input protected against reverse polarity, voltage level|
|Status outputs:||24VDC, max. 30mA|
|Power loss:||max. 18W|
|Soft start / stop:||adjustable via parameters, default setting approx. 0.1 s|
|Degree of protection:||IP 54|
|Radio interference suppression:||acc. to EMC directive|
|Dimensions:||130 x 203 x 135 (width x height x depth)|
|Ambient temperature:||0°C to 40°C|
For more information about our new RNA Smart Control series, please call +49 (0) 241/5109-0.
Control unit for the operation of a vibratory bowl or linear feeder and connection of two sensors to monitor and control the material flow.
Control unit for the operation of two vibratory bowl and/or linear feeders and connection of two sensors to monitor and control the material flow.
The compact control unit type ESK 2.002 are for the Operation of vibratory bowl and linear Feeder with level controller or sensor
Control unit for the operation of a vibratory bowl or linear feeder and connection of two sensors to monitor and control the material flow as well as manual setting of oscillation frequency (e.g.…
ESR 2.500 & ESR 2.800
Control unit for the operation of a vibratory bowl or linear feeder and connection of one sensor to monitor and control the material flow, plus automatic setting of the excitation frequency…
The fequency control unit type ESR 3.000 are for the Operation of one vibratory bowl or linear Feeder and Connection of two sensors for monitoring and controlling the material flow. At the same time…
ESM 906 & ESM 910
Control unit for the operation of a vibratory bowl or linear feeder.
The modules of the ESM 3000 series are designed for operating a vibratory or linear feeding system. A sensor can be connected for monitoring and controlling the material flow and the vibration…
With the SCP 4000, RNA introduces its own PLC offering network connectivity and greater flexibility, which will in future be installed in all feeding systems that require a PLC. The SCP 4000…
Das Steuergerät EBC-3000 ist das Nachfolgemodel unseres bewährten Steuergerätes EBC-3. Bei der Neuentwicklung haben wir besonderen Wert auf Technik, Funktion und Design gelegt. So ist das EBC-3000 …
Steuergeräte der Typenreihe EBF 05 sind mikroprozessorgesteuerte Geräte zur Einstellung der Laufgeschwindigkeit an RNA – Bandantrieben, Steilförderern und Plattenförderern. Zur…